Guide to the Sci.Electronics Newsgroups

Version 1.50

Copyright (C) 1994,1995,1996,1997,1998
Mark Zenier
--- All Rights Reserved ---

Corrections or suggestions to: mzenier@eskimo.com or mzenier@netcom.com


Reproduction of this document in whole or in part is permitted if both of the following conditions are satisfied:
  1. This notice is included in its entirety at the beginning.
  2. There is no charge except to cover the costs of copying.

Introduction

This is the viewers Guide to the USENET Sci.Electronics newsgroups. [June 17, 1997]

This FAQ is a tourist's guide to the various electronics newsgroups.

For more detailed information on the electronics field, try the official (as close as it gets around here) Sci.Electronics.Repair FAQ at http://www.repairfaq.org/ courtesy of Filip "I'll buy a vowel" Gieszczykiewicz, Sam Goldwasser and a cast of thousands.


Some Comments and Q&A.

Some things to remember. These newsgroups are worldwide in coverage. That means that criticizing someone's English, making nationalistic remarks, personal insults, and criticizing another poster's intelligence are invitations to pointless flame wars.

And the computer equipment that will be used to read these messages is anything but uniform. Any extensions that your computer has to support various character sets will not always be reliably transmitted or displayed at the other end. So avoid fancy superscript characters, degrees temperature, greek letters, and line drawing characters like the IBM PC extended character set. There are newer standards for indicating the character interpetation to be used with a posting, but there's no guarentee that the person on the other end is up to date. For the similar reasons, note the discussion on posting software and graphics in the following Q&A section.

You should also consider where a poster is when they request the closest source for some product or information. Not everybody has a Radio Shack in the nearest shopping mall. A common problem is that the toll free 800 numbers common in North America are not easily or cheaply accessible from the rest of the world. Look closely at the orginators domain address to see if they can affordably contact your recommended source.

Keep in mind that various systems and standards are different around the world. Household power voltages and frequencies are different, and the techniques and regulations to deal with wiring are different enough to cause safety problems if you try to use the wrong one. Video systems (orginally tied to the power line frequency) are also widely different around the world. Different scan rates and encoding systems make things incompatible. More recent innovations are even more diverse. For example, stereo audio on television transmissions in the UK, Scandinavian countries, and other parts of Europe is a almost CD quality digital transmission, while in the US, the MTS system is a variation on the analog subcarrier system used for FM stereo.

Not only are the systems different, so is the jargon used to describe them. What might be a Ground Fault Interrupter in North America, would be a Residual Current Circuit Breaker across the Atlantic. And what was written as 4.7 k ohms, might by (from the requirements of the schematic drafting standards) be given as 4k7 ohms.

Q. "Someone has to give me an answer!"

A. Nope, sorry. Everybody here (except a few salesmen) is doing it for their own purposes, and no question is guarenteed to get an answer. Getting obnoxious about it, or repeating the question across every possible newsgroup, or over and over again won't win any friends and marks you as the archetypical "newbie".

Q. "What is crossposting, and is it bad?"

A. Crossposting is where many discussion group names are included in the "Newsgroups" header of a posting. This causes them to be distributed to each of those newsgroups when they are received and processed at a news server. (Note that Usenet is not like the World Wide Web. In contrast to the Web, postings are distributed worldwide to thousands of seperate computer systems, so sending just one message instead of many is beneficial.)

Like many feature of Usenet news, it can be abused. For example, Posting to large numbers of groups at once, or posting to groups that have incompatible discussion topics as a form of harassment. This has gained it a bad reputation that the dogmatic have converted into legendary restrictions.

Try to limit posting to the one newsgroup whose topic matches your subject. If it does seem to overlap a couple of newsgroups' topics, crosspost if you must.

You should avoid (at all cost) multiple postings, (also know as SPAM). This is where you send a seperate posting to multiple newsgroups. This causes several bad things. It creates that much more data that each news server system has to process. It starts a seperate disconnected discussion thread in each newsgroup. And it causes for anyone who reads many of the newsgroups to see the posting repeated for each group. Any competent newsreader software will only show a crossposted message to the reader once, but has no way of dealing with SPAM. (Yes, there is a lot of incompetent software out there.)

Q. Are advertisements restricted to ONLY misc.industry.electronics.marketplace?

A. That's the idea.

Q. Why can't I advertise my [stereo/computer/...] for sale in misc.industry.electronics.marketplace?

A. For the main reason the group is for an audience that isn't interested in buying them. (Note the word 'Industry' in the newsgroup name. If you can buy it at the nearest shopping mall, it doesn't belong here). And the second good reason is there are already well established groups for those purposes. Try the misc.forsale.computers groups, rec.audio.marketplace, rec.video, or rec.radio.swap

Q. Can I post executable binary programs to these groups?

A. No. These are text discussion groups. The amount of resources needed to transmit a program is much greater than the normal posting. Many small sites and individuals use an automatic forwarding system that sends all of the traffic in a newsgroup to them. But often, with a cost determined by the amount of data, or the duration of a phone call (in places where phone use is billed by time). So posting large amounts of data imposes a direct monetary penalty on other users. They don't like it.

For that and other reasons, there a automatic canceling daemon system run by Richard Depew that will erase postings that meet this software's criteria (size and non-text content, and crossposting between text discussion groups and binary posting newsgroups) at all the sites around the world that are set up to accept this software's cancel messages. For more information, read the news.admin.net-abuse.usenet newsgroup.

Beyond that, every program needs a specific combination of computer and operating system, so ANY program will not be useful to a large number of the groups readers.

The alternatives are 1) to set up your own FTP archive or Web page that allows any interested person with a direct Internet connection to get their own copy. (And those without direct connection may have access to systems that will give them access through email.) 2) To get a public archive to put your files onto their system. 3) To post the data to one of the comp.binaries (if the moderator will accept it) or alt.binaries newsgroups, or 4) to offer to email the data to persons who request it.

Q. Can I post graphics images to these groups.

A. Again, this can take a lot of resources and the diversity of formats means that no matter what format you choose, someone will not be able to read it, (even if they are interested). And substituting your graphics scanner for a little thought and writing effort will not win you any friends. So think before you do.

If it is really relevant, use a format that is common, compressed, and encoded so that it can travel over the net in the form of text. If you can't get the file to smaller than about 30 thousand characters after UUencoding or Mime encoding, I'd suggest that you set your files in an archive as discussed above. Also if it's of long term interest, or very specialized interest, no matter what its size. A net posting will only be around for a short time, and putting your work in an acessable archive will make it more widely available. Posting files that are already archived somewhere is a waste of resources. Just include a reference to their location.

File formats that have some supporters are 1) Portable Document Format (.pdf) that have been created with a limited character set so the various network conversions don't corrupt their content. Either through using the 7 bit character conversion in the creation software or by UUencoding or Mime encoding the file. 2) Postscript files that have been compressed with gzip or zip and UU or Mime encoded. 3) GIF files that have been encoded. 4) .bmp or .pcx files that have been compressed and encoded. (Do not waste your time posting uncompressed .bmp files. The Bincanceler will eat them.)

There has been periodic discussions of some file format produced by CAD software, but no one format seems to have wide support.

The same applies to various word processor document file formats. "Everybody" doesn't have the software that you run. And some would rather never have to buy it.

Q. What's the difference between sci.electronic.components, .design, and .equipment?

A. The split here is set up on levels of complexity. In this field of technology, people look for solutions to problems along these levels. Someone who is looking for a box that solves their problems is working at a higher level of detail than someone who is designing a module (circuit board) and that second person is working at a higher level than someone looking for a prebuilt integrated circuit that they need to purchase.

The proposed components group is for questions dealing with individual parts. Someone working on this level is looking for a specific function or source or identification for an electronic component. Postings requesting the identification of an integrated circuit are a large portion of the current traffic.

The design group is for persons combining components into circuits. Discussion on design solutions and techniques.

The equipment group is for persons looking for already available solutions to their problems. In other words, if someone is looking for a solution to their problem, and wants to buy something with a warranty, and that has a salesman and tech support along with it, .equipment is the place to ask for advice. (This is not the place to suggest that the person can go down to Radio Shack and get a 555 and wire up a circuit.)

Q. What's left for sci.electronics.misc?

A. Gossip, history, trivia, manufacturing, systems, standards, announcements ...


Charters and Description Lines

sci.electronics - Circuits, theory, electrons and discussions.

This is now a bogus group. On January 2, 1996, it was superseded by sci.electronics.misc as part of the reorganization vote carried out two months earlier. Expect that access may be turned off or aliased to the new group, and that propagation from system to system will be unreliable.
sci.electronics.basics - Elementary questions about electronics.
"A forum for discussion of electronics where there is no such thing as a stupid question. Beginners questions. Discussion of electronics education. Requests for other sources of information."
sci.electronics.cad - Schematic drafting, printed circuit layout, simulation.
"sci.electronics.cad is an unmoderated group for the discussion of Computer Aided Design software (and systems) for use in designing electronic circuits and assemblies. Topics can include Schematic "Capture" software, Printed Circuit Board layout software, introductory and educational use of circuit simulation software such as Spice, obtaining simulation descriptions (Spice models) for electronic components, and any other computer software that relates to designing electronic circuits at the printed circuit board level."
sci.electronics.components - Integrated circuits, resistors, capacitors.
"Discussions of electronics at the component level. The use, limitations, and identification of resistors, capacitors, integrated circuits, connectors, enclosures, ... and so on. Locations and contact information for Manufacturers, Distributors, and other sources for supply and technical information."
sci.electronics.design - Electronic circuit design.
"Discussions relevant to the design of electronics circuits."
sci.electronics.equipment - Test, lab, & industrial electronic products.
"Discussion of the application and internal operation and relative merits of test equipment, laboratory equipment, and industrial equipment. This is not a forsale group. Buying/selling is supposed to occur in the relocated misc.industry.electronics.marketplace group. (Discussions on the relative merits of various consumer electronics equipment are better held in the groups in the rec hierarchy devoted to those topics.)"
sci.electronics.misc - General discussions of the field of electronics.
"General discussions on the topic of electronics. (Discussions on the relative merits of various consumer electronics equipment are better held in the groups in the rec hierarchy devoted to those topics.)"
sci.electronics.repair - Fixing electronic equipment.
"sci.electronics.repair is an unmoderated group for the discussion of repairing electronic equipment. Topics to include: Requests for assistance, Where to obtain servicing information and parts, Techniques for diagnosis and repair, and Annecdotes about success, failures and problems with equipment manufacturers."
misc.industry.electronics.marketplace - Electronics products & services.
"Advertisement and discussion for the buying, selling, and bartering of electronic components (integrated circuits, resistor, capacitors, etc.), electronics test equipment, electronics laboratory equipment, electronics industrial equipment, and services used for the production of electronics. NO CONSUMER ELECTRONICS - NO AUDIO, VIDEO, or HOME COMPUTERS."

Other Newsgroups of Interest

The following are directly electrical/electronics related: Also some others that aren't:

-- end V1.50 --

This article was written by Mark Zenier and edited by Sam Goldwasser. | [mailto]. The most recent version is available on the WWW server http://www.repairfaq.org/ [Copyright] [Disclaimer]