Installation Notes for Installing the Driver for Windows NT


I.  The OEMSETNT.INF File

The OEMSETNT.INF file is the installation file for the NDIS3 and NDIS4
driver for Windows NT.  The Windows NT Setup program searches first
for an OEMSETUP.INF file for the Windows NT environment.  If the
Setup program does not find such file, the program searches for
the OEMSETNT.INF file.


II.  NT3.51 and NT4.0 Driver Installation

The OEMSETNT.INF file will determine which version of Windows NT you are
installing. The NDIS3 driver IBMEIMP3.SYS will load with NT3.51 and
NDIS4 driver IBMEIMP.SYS will load with NT4.0 and later.

IBM EtherJet ISA Adapter drivers are not included with NT3.51 and NT4.0
therefore you will be required to use the device driver diskette DISK 1.


To install the EtherJet ISA Adapter on your NT4.0 system, perform 
the following steps.

1) From the "My Computer" icon select "Control Panel".  

2) Select "Network" icon and click on "Adapters". Add adapter. 

3) Select "Have Disk...", insert device driver diskette Disk 1 and 
   then select OK.

4) The Select OEM Option window is presented. Make sure that IBM 
   EtherJet ISA Adapters is selected. Select OK. 
   
5) If you are installing a single adapter you are not required to   
   enter the serial number. Select Continue. 
   A serial number is required only when installing multiple adapters.

6) If required enter locally administered address. Select Continue.  

7) By default the EtherJet adapter Duplex Mode is set to Auto negotiate. 
   If you have a hub or switch that does not support Auto negotiate 
   then set the adapter Duplex mode to Full Duplex or Half Duplex. 
   
8) Select required Services, Protocols, and bindings. 

This completes the installation.


To install the EtherJet ISA Adapter on your NT3.51 system, perform  
the following steps.

1) From "Main" icon select "Control Panel" icon.    

2) Select "Network" icon and click on "Add Adapter". 

3) Choose <Other> Requires disk from manufacturer. Continue.

4) You will be promoted to insert the manufacture's diskette.
   Insert the device drivers diskette in drive A. The path is A:\ 
   Select OK. 
    
5) The Select OEM Option window is presented. Make sure the  
   IBM EtherJet ISA Adapter is selected. Select OK. 
   
6) Repeat steps 5, 6, and 7 from NT4.0 installation.

7) Select required Protocols and bindings. 

This completes the installation.



III. Installing the IBM EtherJet ISA adapter on Non Plug and Play machine

The IBM EtherJet ISA adapter was configured with Plug and Play enabled
by default.  To run the NT driver on the Non Plug and Play machine, you
MUST disable the adapter card's Plug and Play hardware. To disable
the Plug and Play hardware, do one of the following procedures:

a>
    1.  Install LANAID on your DOS system. (The LANAID will not work
        on NT system)

    2.  Follow the LANAID user interface to determine whether your system
        is Plug and Plug.

    3.  If your machine is a NON Plug and Play machine, follow the LANAID
        user interface to disable the Plug and Plug hardware on the adapter.
        If your machine is a Plug and Play machine, then do nothing and
        exit LANAID.

    4.  Power off and Power on the machine.

b>
    1.  Boot the machine with LANAIDC.

    2.  Enter /V to view the machine Plug and Play status.

    3.  If your machine is a NON Plug and Play machine, follow the LANAID
        user interface to disable the Plug and Plug hardware on the adapter.
        If your machine is a Plug and Play machine, then do nothing and
        exit LANAID.

    4.  Select and configure the non conflict resources for your adapter,
        such as interrupt, IO base address or Memory Map address.

    5.  Power off and Power on the machine.

III.  Updating the Driver

If you try to Update the IBM EtherJet ISA Adapter driver for Windows NT,
the Setup program may not locate the OEMSETNT.INF file.  This is a known
problem that Microsoft plans to fix.  If you encounter this problem,
use one of the following procedures:

  -- Create a new subdirectory on the Option Diskette and perform the
     Update by using that directory:

     1.  Make a new subdirectory A:\NT on the IBM EtherJet ISA
         Adapter Option Diskette.

     2.  Copy the following files from the root directory to the
         A:\NT subdirectory:
         - OEMSETNT.INF
         - IBMEIWNT.SYS

     3.  In the A:\NT subdirectory, rename the OEMSETNT.INF file to OEMSETUP.INF.

     4.  Use the Windows NT Setup program to perform the Update.
         Note:  When the Setup program prompts you for the path
         of the OEMSETUP.INF file, type A:\NT.


  -- Create a diskette for the Windows NT driver files and perform
     the Update by using that diskette:

     1.  Format a blank diskette.

     2.  Copy the following files from the root directory of the
         IBM EtherJet ISA Adapter Option Diskette to the root directory
         of the second diskette:
         - OEMSETNT.INF
         - IBMEIWNT.SYS
         - DISK1

     3.  Rename the OEMSETNT.INF file to OEMSETUP.INF.

     4.  Use the Windows NT Setup program to perform the Update.