ISDN Primary LAN Distance Server Enabler Install Steps
------------------------------------------------------
 
<Primary Line Requirements>
 
23B+D
Data only including restricted Digital 56Kbps
Separate D channel for each ISDN Primary Line
Base Q.931 Call Control support only
Compatible with AT&T 5ESS. AT&T 4ESS and DMS100 call control support.
 
Once you have a Primary line.
The PRITEST in our install diskette can run under plain OS/2
with our driver to test out if your PRIMARY line is OK.
 
<Software Installation>
 
Please use either process A or process B based on your needs.
A wrap connector on the Primary adapter without a real PRIMARY line
can also be used to complete installation.
 
<It is assumed you have LAN Distance 1.1 and Lan Distance 1.1 CSD.>
 
<A.Installation as a plain Connection Server>
 
It is recommended that the hard disk for install be formatted
unless, the person installing the product is knowledgeable about
the re-install and remove processes associated with currently
installed applications.
 
1) It is assumed that OS/2 Ver 2.1 or higher is installed
and available on the PS/2 Model 95 server.
 
2) Install the LAN Distance version 1.1 software
     Insert the Server Diskette 1 into drive a: and type from the current
     drive a:install.
     You will be asked for the LAPS diskette (diskette 3) and then
     diskettes Server 1 and Server 2.
 
   Install Lan Distance 1.1 CSD as required
 
Shutdown..restart
 
  LAN Distance configuration
 
    Start LAN Distance
     click on Selected..Open As..settings.
 
    The following is a working set-up for a connection server
 
    The following steps may be carried out with directions provided in
    the LAN Distance Advanced Guide V1.1
 
    Workstation..Define Name
 
    Ports..N/A
 
    Modems..N/A
 
    Bridge..Configure Filtering..Values
            Bridge no 1, maximum size 2052
            LAN segment..525 (Dependent on your system)
            hops..8(Dependent on your system)
            Accept frames from specified source addresses only
            LAN_0001...provide addresses if address based filtering done
            Wan no 2 , hops 8
            maximum address 3500
            LAN Type IEEE 802.5
            Let it Generate a LAN address
 
    Answer..start ISDN all calls
            click..change
            ..Select-Enable answer mode on Startup
 
    Phone Book....ISDN
    Timers
       60000,10000,10000
 
shutdown..restart
 
3) Install ISDN Primary Support
     Insert the Primary Server Enable diskette in drive a:
     Go to an OS/2 full screen
     type a:install.
 
     Manually modify config.sys as per install document
     Manually modify WCLNET.INI as per install document
     Manually modify WCLLOCAL.INI as below
 
      {CXDDEFS}
 
         CXD = WCLDIAL.CXD
         ISDNCHANNELS = 23   <--- add this statement
 
shutdown..restart
 
Activate LAN Distance..It will take a few minutes
 
     View ISDNPCML.CUR in the WAL subdirectory.
     The last line should indicate SAPI/TEI 0/0 Established..card #n
 
<B.Installation with CM/2 and 3270 emulation resident at server>
 
It is recommended that the hard disk for install be formatted
unless, the person installing the product is knowledgeable about
the re-install and remove processes associated with currently
installed applications.
 
1) It is assumed that OS/2 Ver 2.1 or higher is installed
and available on the PS/2 Model 95 server.
 
2) If you already have Communication Manager CM/2 ver 1.1 installed
proceed to step 3.
 
Install CM/2...Ignore LAPS install requirement,
    Place Diskette 1 of CM/2 in drive and invoke the following command
    Go to an OS/2 full screen
          a:cmsetup
    Proceed with Set-up and Configuration,
    Configure for Token Ring, 3270 emulation
 
shutdown..restart
 
3)Install LAPS.... Use diskette 3 provided with
  your Lan Distance software product.
    Place LAPS Diskette in drive a: and invoke the following command
    Go to an OS/2 full screen
          a:laps
 
    Configure LAPS
      Select the adapter as
         IBM Token Ring Adapter( or appropriate LAN adapter)
 
      Select the following protocols
 
        0- NETBIOS
        0- IEEE802.2 (or appropriate Protocol)
 
shutdown..restart
 
    Start Communications manager
    Try a VM session and it should work at this point.
    If not, make sure you have the correct version of software for
    OS/2 and CM/2.  Otherwise contact our software support
    as mentioned in the install documentation.
 
4) Install the LAN Distance version 1.1 software
     Insert the Server Diskette 1 into drive a: and type from the current
     drive a:install.
     You will be asked for the LAPS diskette (diskette 3) and then
     diskettes Server 1 and Server 2.
 
   Install Lan Distance 1.1 CSD as required
 
Shutdown..restart
    Start LAN Distance
     click on Selected..Open As..settings.
 
    The following is a working set-up for a connection server
 
    The following steps may be carried out with directions provided in
    the LAN Distance Advanced Guide V1.1
 
    Workstation..Define Name
 
    Ports..N/A
 
    Modems..N/A
 
    Bridge..Configure Filtering..Values
            Bridge no 1, maximum size 2052
            LAN segment..525 (Dependent on your system)
            hops..8(Dependent on your system)
            Accept frames from specified source addresses only
            LAN_0001...provide addresses if address based filtering done
            Wan no 2 , hops 8
            maximum address 3500
            LAN Type IEEE 802.5
            Let it Generate a LAN address
 
    Answer..start ISDN all calls
            click..change
            ..Select-Enable answer mode on Startup
 
    Phone Book....ISDN
    Timers
       60000,10000,10000
 
shutdown..restart
 
5) Install ISDN Primary Support
     Insert the Primary Server Enable diskette in drive a:
     Go to an OS/2 full screen
     type a:install.
 
     Manually modify config.sys as per install document
     Manually modify WCLNET.INI as per install document
     Manually modify WCLLOCAL.INI as below
 
      {CXDDEFS}
 
         CXD = WCLDIAL.CXD
         ISDNCHANNELS = 23   <--- add this statement
 
shutdown..restart
 
Activate LAN Distance..It will take a few minutes
 
     View ISDNPCML.CUR in the WAL subdirectory.
     The last line should indicate SAPI/TEI 0/0 Established..card #n