Flash Changes
                         Model 6589

LUJTxxA is the flash diskette level.
LUKTxxA is the flash image level. (BIOS)
NOTE: All changes carry forward. That is, if a change is added in 01, it is
      also in 02, 03 etc.

CHANGES for LUKT/LUJT21A
Win95 Screen Saver standby hangs
Screen Noise on Windows 3.11 by moving mouse
Fixed day of week  routine for 2000
Cannot exit setup with saving "Default Settings"


CHANGES for LUKT/LUJT22A
System does not detect ECC memory correctly
Partition Magic Misreports HF Capacity
Assigned IO range for PCI devices to 5000h from 4000h


CHANGES for LUKT/LUJT23A
OS/2 Warp gives trap 008; Win95 hangs while booting

CHANGES for LUKT/LUJT24A
Move SMP table from EBDA.
CD Emulation re-boot Fails
System will not work if no video adapter is present.
Suspend does not work in WIN95 with WD HDD and IBM HDD
Will not boot from CDROM with SCSI in system


CHANGES for LUKT/LUJT25A
Dual motor Speed Capability bit isn't set after soft reset
Can't boot NT4.0 when busmaster ide & interg video installed
System will not come up with Etherlink XL in PCI slot
System hangs at CKPT 69h with Adapter 3940 and 2940
System hangs during Win NT lan installation



CHANGES for LUKT/LUJT26A
Greater than 4.2GB IDE HD support added.
Flash Utility reports error with Pentium Pro B1 stepping level chip
PnP BIOS doesn't enumerate correct memory size. Does not show above 16Meg
NMI error. Unexpected int 2 showing up errornously in some old applications
           This was a solid failure.
pci resources not being assigned for multiple video displays
Com1 Modem shows conflicts after reserving in ISA Legacy Resources
PnP BIOS declares system ROM at FFFFE000-FFFFFFFF as RAM
3D Blaster card will not config.
DMI BIOS reporting 32 MB memory on 64 MB system
INVALID WINDOW ADDRESS RETURNED FROM PCI BIOS
Token Ring 16/4 ISA adapter does not work under DOS.
DMA channel 4 shows as available.
PNP devices are not reset during warm boot. This causes intermittant failures
    on re-boot under WIN/95 and possibly WIN/NT. Also can cause devices like CDROMs
    disappear on a warm boot.


CHANGES for LUKT/LUJT27A
95V-Win95 Matrox DriverV3.17.4, Adptr Conflict Err
BIOS update is not compleated when the P6 B1 Step CPU is used
INT 1AH (AX)=B10EH Get IRQ Routing Info destroys ES register.


CHANGES for LUKT/LUJT28A
ATI 3D Impression+ system hangs system on secondary bus.

Olicom PCI Token Ring causes system to hang at checkpoint 02h. This is not the
       only card that may fail. The symptom is a hang during Power On. If you
       the problem you will need to remove your PCI card and reflash to level
       LUKY28A and then re-install the PCI card.


CHANGES for LUKT/LUJT29A

 NOTE:This and newer builds also requires new Infrared drivers for
      WIN95 and OS/2.

 Need IBM specific PnpDevice for FIR to replace generic one
 ECC memory fails with B1 (0619) step level processors.


CHANGES for LUKT/LUJT30A

    Password is being prompted for even when password prompt is off in setup
    SYSTEM may hang if RPL is enabled and a CD-ROM is in the boot sequence
    and the RPL fails.
    16 bit ESS sound card not compatible with bios. This problem could show
    up with many ISA or PNP devices not being recognized.
    Device drivers may hang the system during warm boot. This problem is across
    most systems, however it is highly intermittant. It primarily shows up
    on networked systems during warm boot with high network activity.
    System hangs with 1GB memory installed.

CHANGES for LUKT/LUJT31A
    UNIX applications do not initialize registers before use. This applies to
    some RPL chips and custom applications. We will now clear the upper half
    of extended registers prior to boot.