AdapterID 000C4h AdapterName "Racore 16/4 Token-Ring Adapter" NumBytes 3 FixedResources pos[0]=X1XXX1XXb nameditem Prompt "I/O Address" Choice "I/O A20 - A2F" pos[1]=XXXXXX01b io 0A20h-0A2Fh Choice "I/O A00 - A0F" pos[1]=XXXXXX00b io 0A00h-0A0Fh Choice "I/O A40 - A4F" pos[1]=XXXXXX10b io 0A40h-0A4Fh Choice "I/O A60 - A6F" pos[1]=XXXXXX11b io 0A60h-0A6Fh Help "This selects the I/O addresses the adapter will use. A20h is recommended for most applications, especially for 3270 and AS400 connectivity." nameditem Prompt "Interrupt (IRQ)" Choice "IRQ2 (IRQ9)" pos[1]=XXXX01XXb int 2 Choice "IRQ3" pos[1]=XXXX00XXb int 3 Choice "IRQ10" pos[1]=XXXX10XXb int 10 Choice "IRQ11" pos[1]=XXXX11XXb int 11 Help "Interrupt (IRQ) select. This selects which interrupt (IRQ) line to use. IRQ2 is recommended for most applications, especially for 3270 and AS400 connectivity." nameditem Prompt "ROM Address" Choice "CC000 - CDFFF (8K)" pos[1]=XX00XXXXb pos[2]=XXXX1XX0b mem 0CC000h-0CDFFFh Choice "D0000 - D1FFF (8K)" pos[1]=XX01XXXXb pos[2]=XXXX1XX0b mem 0D0000h-0D1FFFh Choice "D8000 - D9FFF (8K)" pos[1]=XX10XXXXb pos[2]=XXXX1XX0b mem 0D8000h-0D9FFFh Choice "DC000 - DDFFF (8K)" pos[1]=XX11XXXXb pos[2]=XXXX1XX0b mem 0DC000h-0DDFFFh Choice "ROM DISABLED" pos[1]=XX00XXXXb pos[2]=XXXX0XX0b Help "Select the memory location the adapter will use for the ROM. The ROM must be enabled to allow system software to access the Burned-In-Address (BIA). If the ROM is disabled, a network address must be supplied by the user. This can be accomplished by specifying a network address on the command line, or in a configuration file when software is loaded. Refer to driver specific documentation for details on specifying a network address. The ROM must be enabled if Remote Program Load (RPL) is desired." nameditem Prompt "BUS Master Arbitration Level" Choice "Level 8" pos[1]=00XXXXXXb pos[0]=XX10XXXXb arb 8 Choice "Level 9" pos[1]=01XXXXXXb pos[0]=XX10XXXXb arb 9 Choice "Level A" pos[1]=10XXXXXXb pos[0]=XX10XXXXb arb 0ah Choice "Level B" pos[1]=11XXXXXXb pos[0]=XX10XXXXb arb 0bh Choice "Level C" pos[1]=00XXXXXXb pos[0]=XX11XXXXb arb 0ch Choice "Level D" pos[1]=01XXXXXXb pos[0]=XX11XXXXb arb 0dh Choice "Level E" pos[1]=10XXXXXXb pos[0]=XX11XXXXb arb 0eh Choice "Level 0" pos[1]=00XXXXXXb pos[0]=XX00XXXXb arb 0 Choice "Level 1" pos[1]=01XXXXXXb pos[0]=XX00XXXXb arb 1 Choice "Level 2" pos[1]=10XXXXXXb pos[0]=XX00XXXXb arb 2 Choice "Level 3" pos[1]=11XXXXXXb pos[0]=XX00XXXXb arb 3 Choice "Level 5" pos[1]=01XXXXXXb pos[0]=XX01XXXXb arb 5 Choice "Level 6" pos[1]=10XXXXXXb pos[0]=XX01XXXXb arb 6 Choice "Level 7" pos[1]=11XXXXXXb pos[0]=XX01XXXXb arb 7 Help "Select the Arbitration Level in which the card competes to become Bus Master and transfer data to and from the Host. The higher the number, the lower the priority. Not all levels may be available to the user. Conflicts are marked with an asterisk." nameditem Prompt "BUS Master DMA Transfer Mode" Choice "Maximum Burst" pos[2]=XXXXXX1Xb Choice "Minimum Burst" pos[2]=XXXXXX0Xb Help "When transfering data, if Minimum Burst is selected, the adapter will immediately release the bus if another adapter wishes to gain control of the bus. If Maximum Burst is selected, the adapter will continue transfering data up to 7.8 usec after detecting that another adapter wishes to gain control of the bus. Maximum adapter performance will be achieved by selecting Maximum Burst mode." nameditem Prompt "BUS Master Streaming DMA Mode" Choice "DISABLE" pos[2]=XXXXX0XXb Choice "ENABLE" pos[2]=XXXXX1XXb Help "Enabling streaming DMA mode will allow the adapter to transfer data using streaming DMA methods. Enabling this option will not have any effect on machines which do not support streaming DMA." nameditem Prompt "BUS Arbitration Fairness" Choice "ENABLE" pos[0]=XXXXXX1Xb Choice "DISABLE" pos[0]=XXXXXX0Xb Help "If fairness is enabled during the bus arbitration process, the adapter will not request the bus after a transfer has completed until all other adapters which have requested the bus get a turn." nameditem Prompt "Ring Speed" Choice "16 Megabits/Sec" pos[0]=XXXX0XXXb Choice "4 Megabits/Sec" pos[0]=XXXX1XXXb Help "Select the data rate of the ring in which the adapter will run. All adapters on the ring must run at the same speed. You can choose between 4 and 16 megabits/second." nameditem Prompt "Connector/Cable Type" Choice "9 PIN (STP/Type 1)" pos[0]=0XXXXXXXb Choice "RJ45 (UTP/Type 3) or Fiber Optic" pos[0]=1XXXXXXXb Help "Specify which connector that the network cabling is attached to. Normally, Shielded Twisted Pair (STP/Type 1 Cable) is connected to the 9 PIN D connector, and Unshielded Twisted Pair (UTP/Type 3) is connected to the RJ11/RJ45 connector. Be sure to select the 9 PIN connector if you are using a UTP/Type 3 media filter attached to the 9 pin connector. Ensure that you have the proper Multi-station Access Unit (MAU) for the cable type selected. Note that fiber optic or UTP connectors are not available on all models."